How to measure your pool
Use a tape measure and measure the inside of the pool at the waterline, in feet and inches (or meters). Round to the nearest inch; that is plenty.
- Rectangle: length and width.
- Round: the diameter, straight across the middle, inside the wall.
- Oval: length and width at the longest and widest points. Most above-ground ovals have straight sides with rounded ends, so pick Straight sides. If your oval curves all the way round, pick Curved all round; it holds noticeably less.
- Kidney: the length from end to end (L), then the width across the wider rounded end (A) and across the narrower end (B).
- Freeform: use the surface area from your pool plans, or split the pool into rectangles and circles with Add a part. An L-shaped pool is two rectangles; a sun shelf is a shallow rectangle of its own.
Depth means water depth. Measure from the water surface to the floor, not from the top of the wall or the coping. In an in-ground pool, measure at the shallow end and the deep end. If the floor stays flat for a while and then drops into a deeper hopper, the simple average of the two ends is off; use Depth profile and add the break point (where the floor starts to drop) and the deepest point.
Pool volume formulas
Every shape works the same way: find the surface area, multiply by the average depth to get cubic feet, then multiply by 7.4805, the number of gallons in a cubic foot (a US gallon is exactly 231 cubic inches, and 1,728 ÷ 231 = 7.4805; many charts round it to 7.48 or 7.5).
Gallons = surface area (sq ft) × average depth (ft) × 7.4805
Liters = surface area (m²) × average depth (m) × 1,000
| Shape | Surface area |
|---|---|
| Rectangle | L × W |
| Round | π × D² ÷ 4 (about 0.785 × D²) |
| Oval, straight sides | W × (L − W) + π × W² ÷ 4 |
| Oval, curved all round | π × L × W ÷ 4 |
| Kidney | 0.45 × (A + B) × L |
Average depth for a straight slope is (shallow + deep) ÷ 2. For a depth profile the calculator adds up the floor in slices between your points (the trapezoid rule) and divides by the length.
Why charts disagree: some round 7.48 up to 7.5, and the two oval formulas give different answers. A 15 × 30 ft oval with straight sides has 401.7 sq ft of water surface; the curved-all-round formula gives 353.4 sq ft, about 12% less. Use the formula that matches the shape of your pool. The kidney formula is a close estimate, since no two kidneys curve the same way.
Worked examples
In-ground rectangle, 16 × 32 ft, 3 ft 6 in at the shallow end and 6 ft at the deep end:
Area 16 × 32 = 512 sq ft · average depth (3.5 + 6) ÷ 2 = 4.75 ft
512 × 4.75 = 2,432 cu ft × 7.4805 = 18,193 gallons
Above-ground round, 24 ft across, 52 in wall, 46 in of water (46 ÷ 12 = 3.8333 ft):
Area π × 24² ÷ 4 = 452.39 sq ft
452.39 × 3.8333 = 1,734.1 cu ft × 7.4805 = 12,972 gallons
Rectangle with a hopper, 20 × 40 ft: 3 ft 6 in at the shallow wall, 4 ft 6 in at the break point 16 ft out, 8 ft at the deepest point 28 ft out, 7 ft at the deep wall:
Slices: 16 × (3.5 + 4.5) ÷ 2 + 12 × (4.5 + 8) ÷ 2 + 12 × (8 + 7) ÷ 2 = 229
Average depth 229 ÷ 40 = 5.725 ft · 800 sq ft × 5.725 = 4,580 cu ft × 7.4805 = 34,261 gallons
Averaging only the two walls, (3.5 + 7) ÷ 2 = 5.25 ft, gives 31,418 gallons, about 2,800 too few. In a real hopper the sides slope in as well, so the true volume is a little lower than the profile figure. The salt check below tells you how close you are.
Above-ground pools: use the water depth, not the wall
Above-ground walls come in 48, 52 and 54 inch heights, but the water stops below the top. The waterline should sit about halfway up the skimmer opening, which on most pools is 6 to 7 inches below the top of the wall.
| Wall height | Usual water depth |
|---|---|
| 48 in | about 42 in |
| 52 in | about 46 in |
| 54 in | about 48 in |
Approximate gallons at those water depths, worked out with the formulas above (ovals with straight sides):
| Pool | 48 in wall | 52 in wall | 54 in wall |
|---|---|---|---|
| 12 ft round | 2,960 | 3,240 | 3,380 |
| 15 ft round | 4,630 | 5,070 | 5,290 |
| 18 ft round | 6,660 | 7,300 | 7,610 |
| 21 ft round | 9,070 | 9,930 | 10,360 |
| 24 ft round | 11,840 | 12,970 | 13,540 |
| 27 ft round | 14,990 | 16,420 | 17,130 |
| 30 ft round | 18,510 | 20,270 | 21,150 |
| 12 × 24 ft oval | 6,730 | 7,370 | 7,690 |
| 15 × 30 ft oval | 10,520 | 11,520 | 12,020 |
| 16 × 32 ft oval | 11,970 | 13,110 | 13,680 |
| 18 × 33 ft oval | 13,730 | 15,040 | 15,690 |
Your own pool can differ: the water level, a sand cove at the wall, or a dug-out center all change the figure. Measure yours.
In-ground rectangles: typical sizes
| Size | Average depth 4.5 ft | Average depth 5.5 ft |
|---|---|---|
| 12 × 24 ft | 9,700 | 11,850 |
| 14 × 28 ft | 13,200 | 16,130 |
| 15 × 30 ft | 15,150 | 18,510 |
| 16 × 32 ft | 17,240 | 21,070 |
| 18 × 36 ft | 21,810 | 26,660 |
| 20 × 40 ft | 26,930 | 32,910 |
Check your gallons with salt
Tape measurements and formulas are never perfect, and an error in volume carries into every dose. If you add salt (for a salt chlorine generator, for example; the pool salt calculator works out how much), the rise in the salt reading tells you the real volume:
Gallons = pounds of salt added × 1,000,000 ÷ (8.345 × rise in ppm)
Example: 40 lb of salt raised the reading from 3,000 to 3,300 ppm, a rise of 300 ppm. 40 × 1,000,000 ÷ (8.345 × 300) = 15,978 gallons. Test with the same tester before and after, and wait until the salt has dissolved and the pump has mixed it, usually about 24 hours. Chlorine does not work for this check, because some of it is used up as soon as it goes in. The 8.345 is the weight of a gallon of water in pounds: one part per million of anything in a gallon weighs 8.345 millionths of a pound.
Fill time and water cost
Hours to fill = gallons ÷ hose flow (gallons per minute) ÷ 60. To find your hose flow, time how long it takes to fill a 5-gallon bucket and divide 5 by the minutes. At 9 gallons a minute, an 18,193-gallon pool takes about 34 hours. For the cost, multiply the gallons by your water rate; many water bills price water per 1,000 gallons, and some add a sewer charge.
Pool volume questions
How many gallons is a typical pool?
A 16 × 32 ft in-ground pool going from 3.5 to 6 ft deep holds about 18,200 gallons. A 24 ft round above-ground pool with a 52 in wall holds about 13,000. The tables above cover other common sizes.
Why does my number differ from my builder's or the pool's box?
The usual reasons: a different oval formula, rounding 7.48 up to 7.5, a higher or lower water level, or sloped hopper sides that a simple formula does not see. If the gap matters, do the salt check.
How accurate is the result?
As accurate as your measurements. Depth matters most: being 3 inches off on an average depth of 4.75 ft changes the volume by about 5%.
How much does the water weigh?
About 62.3 lb per cubic foot at 70 °F, or a little over 8.3 lb per gallon. The 18,193-gallon example above holds about 151,500 lb, close to 76 tons. The calculator shows the weight of your pool too.
Is my pool saved anywhere?
Save as My pool keeps the result in this browser only, so the pool salt calculator (and our chemical calculators, as they arrive) can fill in your gallons. Nothing is sent to us, and you can remove it at any time with Forget it.
Sources
- US gallon = 231 cubic inches; 1,728 cubic inches = 1 cubic foot: NIST Handbook 133, Appendix E
- Pool area formulas, the 0.45 kidney factor and gallons = area × average depth × 7.48: Sacramento County Environmental Management, pool information sheet and Swimming Pool Calculations (water utility guide)
- Oval factor 6.7 per L × W × depth (matches an oval with straight sides) and rounding to 7.5: Pentair pool catalog, pool volume formulas
- Above-ground waterline halfway up the skimmer, 6 to 7 in below the wall top: The Pool Factory and INYO Pools
- Salt check: pounds = gallons × 8.34 × ppm ÷ 1,000,000 (Florida DEP water treatment formula sheet); the same ratio in a salt table, 267 lb for 10,000 gallons from 0 to 3,200 ppm (Hayward); running the pump 24 hours to spread new salt (Hayward AquaRite owner's manual)
- Weight of water by temperature, 62.30 lb per cu ft at 70 °F: USGS Water Density
Last checked November 22, 2026.
Related calculators
- Pool Salt CalculatorHow much salt to add, in pounds and bags, for your generator's target. Too high? How much water to replace.
- Pool Chlorine CalculatorHow much liquid chlorine, bleach or granules to add, with a target set by your stabilizer (CYA) level.
- Pool Shock CalculatorHow many bags of shock or jugs of liquid chlorine, for a routine shock or to clear algae at the level your CYA needs.
- Pool Stabilizer CalculatorHow much granular or liquid stabilizer to add, or how much water to drain when CYA is too high.
- Pool Alkalinity CalculatorHow much baking soda raises total alkalinity, or how much acid lowers it, in safe rounds.