CalcMyPool

Pool Salt Calculator

Work out how much salt your saltwater pool needs, in pounds and bags, to reach the level your salt chlorine generator was built for. If the salt is already too high, it shows how much water to swap for fresh water.

Not sure? Work it out with the pool volume calculator, then come back.

New or freshly filled pool: 0. Otherwise test with salt strips or a drop kit; a generator's own display can be several hundred ppm off.

Target 3,200 ppm; the manual asks for 2,700 to 3,400 ppm. Low-salt Hayward units (AquaTrol RJLS, marked LS) use far less; pick that option instead.

Bag size
Salt in your fill water

Used only when the salt is too high and you lower it with fresh water. Tap water often has a little; test a glass of it for the exact figure. Leave 0 if unsure.

Salt to add

–

  • –raise
  • 3,200 ppmtarget
  • 2,700–3,400manual range

How it was worked out

To see the result, enter your salt reading.

How much salt to add to a pool

You need three numbers: how many gallons the pool holds, the salt reading now, and the target for your generator. The salt to add is the difference in ppm (parts per million), scaled up to your pool:

Pounds of salt = gallons × (target ppm − current ppm) × 8.345 ÷ 1,000,000
Kilograms of salt = liters × (target ppm − current ppm) ÷ 1,000,000

The 8.345 is the weight of a gallon of water in pounds, so one ppm in one gallon weighs 8.345 millionths of a pound. Example: a 15,000-gallon pool with no salt, aiming for 3,200 ppm, needs 15,000 × 3,200 × 8.345 ÷ 1,000,000 = 400.6 lb, which is 10 bags of 40 lb. This matches the makers' own charts: Hayward lists 267 lb for 10,000 gallons going from 0 to 3,200 ppm.

Pounds of salt to reach 3,200 ppm

Pool sizeFrom 0 ppmFrom 1,500From 2,500From 3,000
10,000 gal267 lb142 lb58 lb17 lb
15,000 gal401 lb213 lb88 lb25 lb
20,000 gal534 lb284 lb117 lb33 lb
25,000 gal668 lb355 lb146 lb42 lb
30,000 gal801 lb426 lb175 lb50 lb

Divide by 40 for the number of 40 lb bags. If your generator's target is not 3,200 ppm, use the calculator above.

Salt level by generator

There is no single right salt level. Each salt chlorine generator is built for its own range, and running outside it can stop chlorine production or wear the cell. The calculator uses the target from the maker's manual:

GeneratorRange in the manualTarget we use
Hayward AquaRite, AquaTrol, Salt & Swim2,700–3,400 ppm3,200 (Hayward's optimum)
Hayward AquaTrol low-salt (RJLS)1,200–1,800 ppm1,500 (Hayward's optimum)
Pentair IntelliChlor IC20, IC40, IC603,000–3,500 ppm3,400 (Pentair's salt charts aim here)
Pentair IntelliChlor Plus, LTat least 3,000 ppm3,600 (Pentair's stated ideal)
Jandy AquaPure, PureLink3,000–3,500 ppm3,200 (inside the range)
Jandy AquaPure Ei4,000–4,500 ppm4,000
CircuPool RJ series3,000–4,000 ppm3,500 (CircuPool's ideal)
Intex Krystal Clear saltwater2,500–3,500 ppm3,000 (Intex's optimum)

Manuals change between model years, so if yours gives a different number, choose Custom target and enter it. Hayward's AquaRite 100 is an exception worth knowing: on pools up to 15,000 gallons it can run on lower salt, from 1,500 to 2,700 ppm.

How to add salt to your pool

  1. Test first. Use salt test strips or a drop kit. A pool that has been chlorinated for years often has some salt already. Pentair notes that its generator's own salt reading can be up to 500 ppm off, so check before buying a large amount.
  2. Buy the right salt. Plain sodium chloride, at least 99% pure (Pentair and Intex ask for 99.8%; check the bag and your manual), sold as pool salt or coarse solar salt. Plain water-softener pellets with no additives work too but dissolve slowly. Avoid rock salt, iodized salt and salt with anti-caking additives or yellow prussiate of soda.
  3. New plaster? Hayward says to wait 10 to 14 days after plastering before adding salt. Ask your builder too.
  4. Add about three-quarters first. With the pump running, pour the salt into the pool itself, not the skimmer, and brush it so it does not sit in a pile. Many manuals, including Intex's, CircuPool's and Pentair's, say to keep the generator switched off until the salt has dissolved.
  5. Run the pump about 24 hours, then test again and add the rest if the reading is still low.

Salt too high? Lower it with fresh water

First, re-test. A reading a little above the range is common, testers disagree by a few hundred ppm, and salt drifts down on its own with splash-out and backwashing. The calculator suggests replacing water only from the maker's own "dilute" level where one is published (Hayward's salt chart: 3,600 ppm; Pentair IntelliChlor: above 4,200 ppm), and otherwise from 500 ppm above the manual's range.

Salt does not evaporate, and no chemical takes it out. The only way down is to replace some of the water. The share to replace is:

Share of water to replace = (current ppm − target ppm) ÷ (current ppm − fill water ppm)

Example: a 15,000-gallon pool at 4,200 ppm, target 3,200, refilled with salt-free water: (4,200 − 3,200) ÷ 4,200 = 0.238, so about 3,570 gallons. Doing it in several smaller rounds is gentler on the pool but uses a little more water. If your tap water has some salt, enter it under Salt in your fill water; it raises the amount to replace.

Why the salt did not rise as expected

If you added the calculated amount and the reading came out far higher or lower, the usual cause is the pool volume. A 20% error in gallons is a 20% error in salt. Turn it around and use the salt to measure the pool: enter the pounds you added and the readings before and after in the salt check on the pool volume calculator. Other causes are salt that has not fully dissolved yet and testers that disagree with each other, so compare readings from the same tester.

Pool salt questions

How many bags of salt for a 15,000-gallon pool?

From no salt to 3,200 ppm, about 400 lb, or 10 bags of 40 lb. For a top-up, enter your current reading above; going from 2,500 to 3,200 ppm takes about 88 lb.

Does pool salt get used up?

No. The generator turns salt into chlorine, and the chlorine turns back into salt. It leaves only with water: splash-out, backwashing, draining and rain that overflows the pool. Evaporation leaves the salt behind.

Will the pool taste salty?

Hayward says most people start to taste salt at about 3,500 to 4,000 ppm. For comparison, CircuPool notes that sea water is around 35,000 ppm, ten times more.

Can I use table salt?

Not iodized table salt or salt with anti-caking agents, which can stain. Plain salt that is at least 99% sodium chloride, with no additives, is fine; some makers ask for 99.8%.

Sources

Last checked November 22, 2026. Always follow your generator's manual and the label on the salt bag.

Related calculators

Salt to add–